Photos
Book
Collection
Videos
Virtual Tours
Pin It Share

Edmonton Power History Foundation Blog

Category: Collection
Results: 41 to 50 of 58

Impedance Bridge

Circa 1960's



Impedance bridge theory developed in 1830's and in the 1840's, C. Wheatstone improved it for accurate resistive/impedance testing. Note "magic eye" tube lower center.

read more

Categories: Instruments Collection

Edmonton Power Sign

EP sign



This was the EDMONTON POWER Sign on the west side of the Rossdale Power Plant The Sign was removed in 1997 when the name was changed to Epcor It is now attached to the Edomonton Power Historical Foundation building

read more

Slate Electrical Panel

1902 - 1930



The panel pictured on the left is from one of the Direct Current (DC) motor generators installed at Rossdale Power Plant before 1915. In the 1960s it was used to control DC power from a motor generator set, which was a back up for the generator exciters ...

read more

Categories: Rectifiers Collection

Foundation Spring Support

Turbine Generator



Clover Bar Generating Station 1969 was the first Power Plant in North America to install a spring supported concrete "Table" foundation The pedestal constructed of concrete posts and beams supported this table. Between the pedesal and table were 126 specially ...

read more

City of Edmonton Crest

Installed 1965



This crest was installed on the west wall of the Rossdale Generating Station in 1966. Upon completion of the last unit, # 10 the station was rated at 405MW. It remained there until 1997 when the name was changed from Edmonton Power to EPCOR.  

read more

Boiler Pressure Gauge

1932



The Boiler Pressure Gauge indicated the steam pressure within the boiler drum. The gauge was located 15 feet above the operating floor and clearly visible from the firing aisle. Manufacturer: The JAS Morgan Brass Manufacturing Company Ltd. Type: Bourden ...

read more

Tags: Gauges

Rossdale Engines

1909 - 1951



Rossdale Power Plant had several steam engine-driven generators over the years. At least five of them were made by Belliss and Morcom. The triple expansion 750 kW Direct Current (DC) was installed to power the street railway and used until 1951.

read more

Clover Bar Generating Station Model

1969



This is a model of the first 165 MW turbine-generator at the Clover Bar Generating Station. The model was supplied by Escher Wyss and built to a scale of 1/4" = 1 foot. The Clover Bar Generating Station was built between 1967 and 1969. Manufacturer: Albert ...

read more

Tags: Clover Bar

Rossdale Office Furniture

1930



This furniture was used in the Rossdale General Office around 1931. It is made of mahogany .    This is the table and chairs from the 1931 Office building

read more

Steam Drum Suspension



The steam boilers used in power plants can weigh several hundred tonnes. When a flame is inserted into the boiler furnace, the temperature of the boiler increases by several hundred degrees, thereby increasing the size of the boiler by as much as 3 inches ...

read more

Tags: Clover Bar

Edmonton Power Historical Foundation

Location: 

We are located on the grounds of the Leduc West Antique Museum. Travel 5 km west of Leduc on Highway 39. Go north on Range Road 260 (Cohne Dale Road) for about 800 metres and the museum will be on your right. 

Hours of operation 2024

Well, that's just about it for 2024. The final show was the Lesco Pro Truck show on 21-Sept, and it was a HUGE success; lots of people on site and lots of visitors to our museum. The next event will be the Leduc Country Lights all through the month of December. The whole park will be lit up in a breathtaking display of thousands of lights covering 8 acres. Unfortunately, the EPHF Museum will not be open to visitors for this show. If, however, you are interested in a private tour, just leave a message on this website and we'll do our best to arrange a time for you to come out.
We'll open again in May 2025 for the Leduc West Spring Swap Meet, dates to be announced. Watch this space.
 

 

Leave us a message

 
 
Top